Zhuohang Precision Machining Factory

Mechanical Components Quality Control

The material-to-process match only works if the material is what the drawing says. A 303 run as 304, or a 6061 run as 7075, changes the machinability, the finish, and the service life — even when every dimension is right. XRF verification keeps the match honest.

The failure is silent. A 6061 part machined from a 7075 bar will measure correctly and still fail in service because the alloy properties were never what the drawing assumed. That is why verification sits before the first chip, not after the last inspection.

The verification also protects the process plan itself. The feeds, speeds, and tooling were chosen for a specific alloy; run a different alloy through the same plan and the cut is wrong before the dimension is ever checked. Verification is what lets the planner trust the plan.

Which certifications back the quality system?

Quality control process flow, Zhuohang Precision Machining Factory, Dongguan, China
StandardCertificate numberScope
ISO 9001:2015116024/A/0001/UK/EnMachining of metal parts
IATF 16949:2016131941/A/0001/SM/EnManufacture of CNC metal machining parts (excludes product design, Clause 8.3)
ISO 14001:2015116024/B/0001/UK/EnEnvironmental management related to machining of metal parts

Honest scope note: IATF 16949 excludes product design under Clause 8.3. We are a build-to-print manufacturer — you own the design, and we own making it repeatably to your print.

The numbers are stated so they can be checked with the registrar. A certificate number that a shop will not share is a certificate a buyer cannot confirm, and an unconfirmed certificate is a claim, not a fact.

Three standards cover three promises. ISO 9001 covers the quality system, IATF 16949 adds the automotive-grade discipline on top, and ISO 14001 covers the environmental management around the machining. Together they describe the full shape of the plant's accountability.

What does SPC and Cpk actually measure?

SPC is statistical process control: the shop measures a characteristic on parts over time and charts the result, so a drift shows up as a trend before it shows up as a reject. Cpk is the single number that compresses that history into how much margin the process keeps inside the tolerance band.

Cpk is not the average; it is the spread against the band. A process can be perfectly centered and still fail if the spread is wide, because some parts will land near the edge. A high Cpk means the process is both centered and tight, with real room before a part drifts out of spec.

The difference between "we inspect" and "we are in control" is exactly this. Inspecting parts catches bad parts after they are made; SPC catches a process that is drifting before it makes bad parts. If you ask for the Cpk chart, not a single measurement, you are asking for the stronger promise.

What process capability does the shop prove?

A capability statement is worthless without a control chart. On a representative length characteristic (76.1–76.5 mm), our SPC shows Cpk 1.851 (one characteristic on one part, not a blanket capability claim) against an initial-study target of Ppk ≥ 1.67, with general characteristics held to Cpk ≥ 1.33. That is a measured result.

Cpk measures spread against the tolerance band, not just the average. A process can be centered and still fail if the spread is wide; a Ppk ≥ 1.67 at the initial study on key characteristics means the distribution sits well inside the band with margin, on a dimension the shop actually controls. That number is the difference between "we inspect" and "we are in control."

The two thresholds — 1.67 for key characteristics and 1.33 for general ones — are the shop's own bar. Key characteristics, the ones a failure would break, get the tighter requirement; general characteristics get the floor. The distinction is what separates the dimensions that matter from the ones that just have to be right.

How is a part inspected before it ships?

The inspection bench is the same class of equipment a buyer would use to audit us, and the results are documented.

Each instrument answers one question: the CMM answers "is it the right size," the laser microscope answers "is the surface right," the XRF answers "is it the right material," and the hardness and tensile testers answer "will it survive." Together they close the loop from bar to shipped part.

The bench is not a showpiece; it is the audit trail. Every reading is recorded against the part and the lot, so you can ask for the dimensional report on a specific feature and receive it. A bench that cannot produce the report is a bench that is only for display.

How does material traceability protect the buyer?

Quality inspection at Zhuohang Precision Machining Factory for mechanical components
Dimensional inspection of components

A material certificate with a heat number follows every batch, tying the parts back to a verified lot. If a part fails in service, the first question is almost always "was it the right material?", and the certificate answers it before it is asked. Our MES/ERP system records the full chain on every lot.

The trace also runs in reverse. If a heat number is tied to a batch and a batch to a shipment, a single suspect lot can be isolated without scrapping everything the shop ever made. That is the quiet value of the certificate: it shrinks a worst-case recall into a narrow, findable band.

Traceability is the thread that ties the whole quality system together. The XRF confirms the bar, the certificate names the heat, the MES/ERP records the route, and the final report ties the part back to all three. If you hold that thread, you can pull on it at any point and the whole chain answers.

Can the shop provide a PPAP package?

Zhuohang Precision Machining Factory quality-controlled factory in Dongguan
The quality-controlled Dongguan facility

For automotive and regulated buyers, a PPAP package proves the process is under control. Our APQP/PPAP evidence includes process flow charts, control plans, SPC charts, and PFMEA — the same discipline an IATF 16949 audit looks for.

The documents are not decoration. A process flow chart shows the route, a control plan states how each characteristic is held, an SPC chart shows it is held, and a PFMEA shows what was thought through before the first run. If you ask for these, you are asking for evidence, not a promise.

PPAP is also where the material-to-process match gets written down. The process flow names the machine each feature runs on, the control plan names the characteristic and its tolerance, and the SPC chart proves the process holds it. The match, which starts as a planning decision, ends as a documented, auditable record.

What does a control plan contain?

A control plan is the bridge between the drawing and the floor. For each characteristic that matters, it states the specification, the measurement method, the instrument, the sample size, and the frequency, so the operator and the inspector both know what "right" means and how to prove it.

The control plan is what turns "we check parts" into "we control a process." It names every characteristic that matters, says how it is held, and — critically — says what happens when it is not. A shop without a reaction plan is a shop that discovers problems after they ship.

you should ask to see the control plan for their part before the first run. The plan is the shop's written answer to "how will you hold my tolerances," and a shop that can produce it is a shop that has already thought the process through.

How does APQP and PFMEA close the loop?

APQP is the planning discipline that runs before production: define the part, plan the process, validate it, and only then release it to volume. PFMEA is the risk half of that discipline — it walks each step and asks what could fail, how likely, and how badly, then writes the control that prevents it.

The two together close the loop that inspection alone cannot. Inspection catches a bad part; APQP and PFMEA stop the bad part from being planned in the first place. A shop that runs APQP has already thought about the failure modes before the first chip, so the control plan is a prevention, not a reaction.

For you, the PFMEA is the honest document. It lists what could go wrong with the part and what the shop is doing about it, which is the opposite of a sales sheet. A supplier that hands you its PFMEA is showing you its thinking, warts and all, and that openness is exactly what a build-to-print buyer should pay for.

What quality evidence should a buyer request?

Ask for these before the first order, not after a failure.

What this shop actually runs

We machine every part in our own 6,800 m² plant in Dongguan, China, on 100+ CNC machines with 100+ staff. The machine list by category:

  • 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Meant for compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
  • 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Meant for prismatic parts, plates, brackets, housings.
  • Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Meant for long, slender rotational parts at ±0.002 mm.
  • CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Meant for shafts, bushings, flanges up to ±0.002 mm.
  • Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Meant for hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
  • Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
  • Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.

Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk >= 1.67 initial on key characteristics, Cpk >= 1.33 ongoing.

Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.

Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.

Contact: Felipe Iglesias, [email protected], +86 13126536955.

Verify the material and the quality system

Email [email protected] or call +86 13126536955 and ask for the certificate numbers, a Cpk chart, and a material certificate.

Frequently Asked Questions

Why is material verification the first line of quality?

A mixed or mislabeled bar defeats every process decision downstream. XRF-checking incoming material against the mill certificate catches a wrong alloy at the door, before it becomes a wrong part in your product.

Which certifications back the quality system?

ISO 9001:2015 (No. 116024/A/0001/UK/En), IATF 16949:2016 (No. 131941/A/0001/SM/En), and ISO 14001:2015 (No. 116024/B/0001/UK/En). The IATF 16949 scope excludes product design under Clause 8.3.

What does SPC and Cpk actually measure?

In short, SPC tracks a measured characteristic over time, and Cpk compresses that history into one number: how much margin the process keeps inside the tolerance band. A higher Cpk means the process is centered and tight, with room before a part drifts out of spec.

What process capability does the shop demonstrate?

In short, On a representative length characteristic (76.1–76.5 mm), the SPC shows Cpk 1.851 (one characteristic on one part, not a blanket capability claim) against an initial-study target of Ppk ≥ 1.67, with general characteristics held to Cpk ≥ 1.33. One more check on that number: the 0.4 mm band behind it is wide by design, so the same process spread held against a ±0.003 mm (milling) / ±0.002 mm (turning) feature would fail outright.

How are parts inspected before they ship?

Critical dimensions are verified on Hexagon GLOBAL S CMMs, supported by a KEYENCE VK-X3000 laser microscope, a SURFCOM 1800D for surface finish, an XRF spectrometer for material, and hardness, coating-thickness, salt-spray, and tensile testers.

Can the shop provide PPAP and control plans?

Yes. The automotive-grade APQP/PPAP package is supported by process flow charts, control plans, SPC charts, and PFMEA, reflecting the IATF 16949 build-to-print discipline.

Standards referenced on this page

  • IATF 16949:2016 — Automotive quality management system standard
  • ASTM B211/B211M-19 — Standard Specification for Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
  • ISO 14001 — Environmental management systems — Requirements with guidance for use