Mechanical Components Services
Mill-turn puts turning and milling on one machine, so a part that is mostly round but carries a milled flat, a cross-hole, or a keyway is cut in a single setup. The round features and the prismatic features share one datum, and nothing is lost in a hand-off.
The single setup is the point. A shaft with a cross-drilled hole that moves from the lathe to the mill has to be re-indicated, and any error in that re-indication lands in the part. Mill-turn removes the hand-off, so the hole stays true to the axis it was turned around.
The service uses mill-turn for the parts where the mix of round and flat features is real — the shaft with a keyway, the boss with a side flat, the fitting with a wrench hex. When the geometry is simple, plain turning or milling is still the cheaper route; mill-turn earns its cost only where it removes a setup.
What does precision grinding add?
Grinding is the finishing service for the surfaces that have to be round, flat, and smooth beyond what turning or milling can hold. It runs to ±0.002 mm and delivers the surface finish that a bearing seat or a sealing face demands.
The service grinds surface, centerless, and cylindrical work on 7+ machines, so a hardened shaft, a flat die face, or a long thin pin can all reach their finish dimension. Grinding is also what follows heat treatment: a part that is hardened to wear resistance is ground back to size after the heat treat moved it.
Grinding is not applied everywhere — it is applied where the tolerance earns it. A part that needs ±0.003 mm (milling) / ±0.002 mm (turning) stays on the mill or lathe; a part that needs ±0.002 mm and a controlled Ra goes to the grinder. The service states which surfaces earn the grinding pass and why, instead of grinding everything by default.
How is material verified before it reaches a machine?
The first failure in a component is often the material, not the machine. Incoming bar is XRF-checked against its mill certificate so a mixed or mislabeled lot is caught at the door, and a material certificate with a heat number follows the batch through production.
A service that cannot show this step is asking you to trust the alloy on faith. The XRF check takes the material claim out of the sales conversation and turns it into a recorded reading.
The mill certificate names the grade, the heat number, and the test results; the XRF confirms the physical bar matches the paper. Both follow the batch, so a part can be traced to the heat that made it. For the service, that trace is the difference between machining a part and machining a known material.
Which finishing does each material accept?
The alloy sets which finishes are practical, and a mismatch shows up as a service failure. The service pairs the material with the finish that works.
- Aluminum: standard and hard anodizing, powder coating, painting.
- Steel: zinc / nickel / chrome plating, carburizing, nitriding.
- Stainless: passivation, electropolishing, bead blasting.
- Copper / brass: silver, gold plating for conductivity.
- All materials: brushing, polishing, deburring.
The alloy sets the finishing menu, and a service that ignores the menu will plate what the alloy cannot hold. Pairing the two up front is what keeps a finish from becoming a warranty claim.
Finishing also carries a dimensional cost. Anodize and plating add thickness, and a tight bore or thread has to be machined with that allowance in mind. The service folds the finish into the machining allowance before the part is cut, so the finished part measures right instead of binding.
When does heat treatment enter the match?
Heat treatment is a material decision. Alloy steel gets carburized or nitrided for wear; 17-4PH stainless gets precipitation-hardened; aluminum gets aged. Our in-house ovens reach 500 °C, covering aluminum aging and low-temperature steel stress relief. Titanium stress relief above that goes to a qualified partner, stated honestly.
Heat treatment re-enters the material after machining, so the service sequences it into the route rather than bolting it on. A carburized part is machined with stock, hardened, then finish-ground — the order is the quality.
The service also discloses the split honestly. The steps the ovens cover run in-house; the steps that need a higher temperature go to a qualified partner, and that hand-off is stated rather than hidden. You should read that disclosure as the service knowing where its capability ends.
What tolerance does the service hold on each alloy?
Tolerance is partly a material property. Milling and turning hold ±0.003 mm (milling) / ±0.002 mm (turning) and grinding holds ±0.002 mm, with Ppk ≥ 1.67 at the initial study on key characteristics, verified on Hexagon CMMs. The service applies that capability where the alloy and the process can both support it.
| Process | Held tolerance | When it applies |
|---|---|---|
| CNC milling | ±0.003 mm | Stable alloys — aluminum, steel, brass |
| CNC turning | ±0.002 mm | Steel, stainless, brass, titanium |
| Precision grinding | ±0.002 mm | Hardened bearing seats, roundness-critical surfaces |
A tolerance only counts where the alloy can hold it. A soft plastic will not hold a grinding tolerance, and a hardened seat will not hold a milling tolerance — the service states the capability per material, not as one blanket number.
The tolerance also carries a cost ladder. A ±0.1 mm part needs a standard setup; a ±0.003 mm (milling) / ±0.002 mm (turning) part needs a controlled process and CMM verification; a ±0.002 mm surface needs grinding. The service quotes the tolerance the function actually needs, so you pay for the precision that matters and nothing more.
How does the service handle prototypes and single parts?
The service takes one piece, because the minimum order is one piece. A prototype can be machined, measured, and validated on the same drawing and process that later runs the volume, so the first article and the production part come from the same route.
The value of the single part is that it de-risks the volume. You validate the material-to-process match on one part — the alloy cuts clean, the finish takes, the dimension holds — before committing to a run. When the match is proven on the prototype, the production run is a repeat, not an experiment.
The same service scales in both directions. A one-off fixture and a thousand-part run share the floor and the inspection bench, so there is no "prototype shop" and "production shop" gap where the process quietly changes between the two. The part you validated is the part you receive.
What red flags signal a material-matching gap?
These signals separate a service that matches from one that hopes.
- No material verification. A service that does not XRF-check incoming bar cannot prove the alloy is what you ordered.
- Finishing treated as an afterthought. A quote that ignores what the alloy accepts will fail in service.
- No process rationale. A service that cannot say why a material goes to milling versus turning is guessing.
- Blanket tolerance. One tolerance for every material and every process means the service is not reading your print.
- Hidden subcontract. Finishing or heat treatment sent out without disclosure breaks the chain of accountability.
What should a buyer ask the service?
Run the service through these before you commit a drawing.
- Which machine does each alloy on my print go to?
- How do you verify the incoming bar?
- Which finishes does my alloy accept, and who applies them?
- What tolerance and Cpk does each process hold on my material?
- Which steps are outsourced, and how are they controlled?
- Does the prototype run the same route as production?
What this shop actually runs
We machine every part in our own 6,800 m² plant in Dongguan, China, on 100+ CNC machines with 100+ staff. The machine list by category:
- 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Meant for compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
- 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Meant for prismatic parts, plates, brackets, housings.
- Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Meant for long, slender rotational parts at ±0.002 mm.
- CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Meant for shafts, bushings, flanges up to ±0.002 mm.
- Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Meant for hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
- Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
- Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.
Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk >= 1.67 initial on key characteristics, Cpk >= 1.33 ongoing.
Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.
Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.
Contact: Felipe Iglesias, [email protected], +86 13126536955.
Get your material matched to the right process
Send your drawing to [email protected] or call +86 13126536955 for a material-to-process recommendation and quote.
Frequently Asked Questions
How does the service match material to process?
In short, Each alloy is routed to the machine that cuts it best and paired with the finishing it accepts. Aluminum is milled and anodized; steel is turned, hardened, and plated; brass is turned for conductivity.
Which machining services run in-house?
CNC milling (3-, 4-, and 5-axis), CNC turning, mill-turn, and precision grinding all run in-house. Surface finishing and some heat treatment are outsourced to qualified partners and disclosed rather than implied.
What does mill-turn add over separate milling and turning?
Mill-turn cuts round and prismatic features in a single setup, so a part with a shaft and a cross-hole or a milled flat keeps one datum instead of losing tolerance in a hand-off between two machines.
What tolerances does the service hold?
Milling and turning hold ±0.003 mm (milling) / ±0.002 mm (turning) and grinding holds ±0.002 mm, with Ppk ≥ 1.67 at the initial study on key characteristics and ≥ 1.33 on general characteristics, verified on Hexagon CMMs.
What is the minimum order quantity?
One piece. The service takes prototype and single-part orders as well as production runs, so you can validate a design on a first article before committing to volume.
How is material verified before machining?
Incoming bar is XRF-checked against its mill certificate so a mixed or mislabeled lot is caught at the door, and a material certificate with a heat number follows the batch through production.
How do I get a material and process recommendation?
Email your STEP, IGES, or 2D drawing to [email protected]. The reply includes a DFM review with a material-to-process recommendation and an itemized quote.
Standards referenced on this page
- ASTM B211/B211M-19 — Standard Specification for Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
- ASTM B348/B348M-21 — Standard Specification for Titanium and Titanium Alloy Bars and Billets
- ISO 9001 — Quality management systems — Requirements
